Swansoft Sim SINUMERIK English, CNC, CNC, SYMULATOR CNC PL
[ Pobierz całość w formacie PDF ]
NANJING SWANSOFT
SWAN NC SIMULATION
SOFTWARE
SINUMERIK SYSTEM
INSTRACTION OF OPERATION AND
PROGRAMMING
Nanjing Swan Software Technology Co.,Ltd.
Version 05/2007
CONTENTS
CHAPTER 1 SUMMARY OF SWAN NC SIMULATION SOFTWARE .................1
1.1 BRIEF INTOUCTION OF THE SOFTWARE................................................1
1.2 FUNCTION OF THE SOFTWARE ................................................................1
1.2.1 CONTROLER.......................................................................................1
1.2.2 FUNCTON INTRODUCTION.............................................................3
CHAPTER 2 OPERATIONS OF SWANSC NC SIMULATION SOFTWARE ........5
2.1 STARTUP INTERFACE OF THE SOFTWARE.............................................5
2.1.1 STARTUP INTERFACE OF PROBATIONAL VERSION..................5
2.1.2 STARTUP INTERFACE OF NETWORK VERSION .........................5
2.1.3 SINGLE MACHINE VERSION STARTUP INTERFACE..................7
2.2 SETUP OF TOOLBAR AND MENU .............................................................8
2.3 FILE MANAGEMENT MENU.......................................................................9
2.3.1 MACHINE PARAMETER .................................................................10
2.3.2 CUTTER MANAGEMENT ...............................................................12
2.3.3 WORKPIECE PARAMETER AND ACCESSORY ...........................14
2.3.4 RAPID SIMULATIVE MACHINING ...............................................17
2.3.5 WORKPIECE MEASUREMENT......................................................17
2.3.6 REC PARAMETER SETUP...............................................................17
2.3.7 WARING MESSAGE .........................................................................18
CHAPTER 3 SINUMERIK 802S/c OPERATION......................................................21
3.1 SINUMERIK 802S/c MACHINE PANEL OPERATION .............................21
3.2 Operation button ............................................................................................22
3.2.1 EYSTOKE INTRODUCTION ........................................................22
3.2.2 MANUAL OPERATION OF VIRTUAL NC MACHINE...............23
3.3 NC SYSTEM OPERATION ..........................................................................23
3.3.1 Parameter Mode ..................................................................................23
3.3.2 Manually Operated Mode ...................................................................27
3.3.3 Automatic Mode..................................................................................28
3.3.4 Program Mode ....................................................................................30
CHAPTER 4 SINUMERIK 802D OPERATION ........................................................33
4.1 SINUMERIK 802D MACHINE PANEL OPERATION ............................33
4.2 Operation button .........................................................................................35
4.2.1 EYSTOKE INTRODUCTION ........................................................35
4.2.2 MANUAL OPERATION OF VIRTUAL NC MACHINE...............36
4.3 NC SYSTEM OPERATION ..........................................................................36
4.3.1 Parameter Mode ..................................................................................36
4.3.2 Manually Operated Mode ...................................................................39
4.3.3 Automatic Mode..................................................................................40
4.3.4 Program Mode ....................................................................................43
CHAPTER 5SINUMERIK 810/840 OPERATION.....................................................45
5.1 SINUMERIK 810/840D MACHINE PANEL OPERATION .....................45
5.2 Operation button ............................................................................................46
5.2.1 EYSTOKE INTRODUCTION ...........................................................46
5.2.2 MANUAL OPERATION OF VIRTUAL NC MACHINE .................47
5.3 NC SYSTEM OPERATION ..........................................................................48
5.3.1 Manually Operated Mode ...................................................................48
5.3.2 Parameter Mode ..................................................................................48
5.3.3 Automatic Mode..................................................................................50
CHAPTER 6 SINUMERIK 801 OPERATION ...........................................................52
6.1 SINUMERIK 801 MACHINE PANEL OPERATION ..................................52
6.2 Operation button ............................................................................................53
6.2.1 EYSTOKE INTRODUCTION ...........................................................53
6.2.2 MANUAL OPERATION OF VIRTUAL NC MACHINE...............54
6.3 NC SYSTEM OPERATION ..........................................................................54
6.3.1 Manually Operated Mode ...................................................................54
6.3.2 Parameter Mode ..................................................................................55
6.3.3 Automatic Mode..................................................................................58
6.3.4 Program Mode ....................................................................................59
CHAPTER 7 SINUMERIK 802Se OPERATION .......................................................61
7.1 SINUMERIK 802Se MACHINE PANEL OPERATION ..............................61
7.2 Operation button ............................................................................................62
7.2.1 EYSTOKE INTRODUCTION ...........................................................62
7.3 NC SYSTEM OPERATION ..........................................................................63
7.3.1 Parameter Mode ..................................................................................64
7.3.2 Manually Operated Mode ...................................................................68
7.3.3 Automatic Mode..................................................................................69
7.3.4 Program Mode ....................................................................................71
CHAPTER 8 SINUMERIK 802D programme............................................................73
8.1 Position .......................................................................................................73
8.2 G Commands .................................................................................................76
8.2.1 Fundamental Principles of NC Programming.....................................76
8.2.2 Positional data ..................................................................................85
8.3 Overview of cycles ........................................................................................97
8.4 Arithmetic Parameters R .............................................................................. 118
8.5 Local User Data ........................................................................................... 119
CHAPTER 9 SINUMERIK 802S/c programme.....................................................122
9.1 Position .....................................................................................................122
9.2 G Commands ............................................................................................125
9.2.1 Linear interpolation at rapid traverse:...............................................125
9.2.2 Positional data ................................................................................126
9.3 CYCLES ......................................................................................................137
9.4 Arithmetic parameters R ..............................................................................153
9.5 Program jumps ..........................................................................................155
9.5.1 label --- Jump destination for program jumps................................155
9.5.2 Unconditional program jumps ..........................................................155
9.5.3Conditional program jumps ...............................................................155
9.5.4 Programming example ......................................................................156
9.6 Subroutine ....................................................................................................157
CHAPTER 10 SINUMERIK 810/840 programme....................................................160
10.1 Position ...................................................................................................160
10.2 G Commands .............................................................................................164
10.2.1 Fundamental Principles of NC Programming.................................164
10.2.2 Positional data ..............................................................................172
10.3 Overview of cycles ....................................................................................184
10.4 Arithmetic Parameters R ............................................................................205
10.5 Local User Data .........................................................................................206
CHAPTER 11 SINUMERIK 802Se programme .......................................................209
11.1 Position....................................................................................................209
11.2 G Commands...........................................................................................212
11.2.1 Linear interpolation at rapid traverse: .............................................212
11.2.2 Positional data ..............................................................................212
11.3 CYCLES .................................................................................................224
operation manual SSCNC introduce
CHAPTER 1 SUMMARY OF SWAN NC SIMULATION
SOFTWARE
1.1 BRIEF INTOUCTION OF THE SOFTWARE
Based on factories’ manufacturing and colleges’ teaching experience, Nanjing Swan
Software Technology Co., Ltd developed the following software: FANUC, SIMUMERIK,
MITSUBISHI, GSK, HNK, KND, DASEN, and simulation software. Through which, we can
attain the aim of enabling students to have the experience of practical manipulation on a
largely-reduced cost.
Swan series NC simulation software can be furthere devided in 8 major types, 28systems
and 62 controlling surfaces. Equipped with FANUC, SIMUMERIK, MITSUBISHI, GSK, HNK,
KND, DASEN software, swan NC simulation software can help students to learn operation of NC
milling tool, lathe and machining center of each system. Meanwhlie CAM NC program can be
programmed or read in by manual.By internet teaching,teachers can have the first-hand
information of their students’current manipulating condition .
1.2 FUNCTION OF THE SOFTWARE
1.2.1 CONTROLER
1. The screen configrations can be realized and all the functions are the same with CNC
machine used in the industrial system.
2. Interprets NC codes and edits cutting feed commands of machine real-timely.
3. Operation panels are similar with the real NC machine can be provided.
4. Single brick operation
，
automatic operation,editing pattern,dry running,and so on.
5. Rate of travel adjusting, change over switch of unit millimeter pulse.
1
[ Pobierz całość w formacie PDF ]